2″ Eyeball Gimbal
Adjustable yet air-tight without housing needed.
Spec & Sell Sheets
Product Features
- Models: 5W: LL2G, High Output 5.5W: LL2G-HO
- Type IC Rated – Approved for Direct Contact with Insulation
- Air-Tight, Wet Location, Insulated and Non-Insulated Ceilings
- Superb Light Quality with CRI 90+
- Color Temperatures: 2700K / 3000K / 3500K / 4000K / 5000K / Dim to Warm 3000-1800K
- Light Output 5W: 2700K – 380 lm, 3000K – 400 lm, 4100K – 430 lm
- Light Output 5.5W: 2700K – 450 lm, 3000K – 490 lm, 3500K – 500 lm, 4000K – 530 lm, 5000K – 550 lm, Dim to Warm – 430 lm
- External Driver Inside Connection Box – No Junction Box Needed
- Default Driver 120V input Triac dimmable with most CL Dimmers
- Optional Driver for 5.5W model: 120V-347V input 0-10V Dimmable
- Recessed Housing is NOT Required even for Insulated Ceilings
- Warranty: 10 Year on Residential, 5 Year on Commercial Installations
- cULus Listed, Energy Star (except Dim to Warm)
Video Overview
Discover Eyeball Gimbal LED Lights
Technical Specifications
CONSTRUCTION:
2″ Eyeball Gimbal fixture with integral LEDs. Class 2 Isolated external driver factory installed inside junction box.
One driver for every fixture required.
MOUNTING:
Cut hole in ceiling and snap fixture in opening with attached spring clips.
Ceiling Clearance Required: 1 1/2″ with driver remotely installed, 5″ if driver is next to the fixture.
- Default Driver: 120V input Triac Dimmable with most CL dimmers
- Optional Driver for 5.5W HO model: 120V-347V input 0-10V Dimmable
- Energy Used: LL2G 5W, LL2G-HO 5.5W,
- Power factor: > 0.95
- Beam Angle: 36° Beam with 20° tilt and 360° rotation
- Color Temperatures: 2700K / 3000K / 3500K / 4000K / 5000K / Dim to Warm 3000-1800K
- Light Output 5W: 2700K – 380 lm, 3000K – 400 lm, 4100K – 430 lm
- Light Output 5.5W: 2700K – 450 lm, 3000K – 490 lm, 3500K – 500 lm, 4000K – 530 lm, 5000K – 550 lm, Dim to Warm – 430 lm
- CRI 90+
- Ambient Operating Temperature: -40°F (-40°C) to +104°F (+40°C)
- Compliance: cULus approved, certified to CSA STD. C22.2 No. 250.0
- Rated: Type IC (Direct Contact with Insulation), Air-Tight, Wet Location
DIMENSIONS:
- ID 2″, OD 2 1/2″; Thickness 1 1/2′
- Cut out: 2″ 1/8″
- Junction Box Dimensions (with driver inside): 3 3/4″ x 2″ x 1 3/4″
Suitable for wet locations and soffit installations.
Installation
ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.
Gimbal LED Lights Installation:
CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove the knockout on the side plate. Install standard L16 cable connector. Insert line voltage feed into the cable connector and splice same colour wires using the included quick connectors. Close the cover. Connect the driver to the light fixture – the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand.
OPTIONS FOR LOCATING DRIVER:
Fixture comes connected to the driver by 15″ long low voltage cable with waterproof connector in the middle.
Depending on where you want the driver to be you have 2 options:
- Locate next to the fixture.
- Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 6 feet (1.8m) and 20 feet (6m). Cables are linkable.
Maximum run should not exceed 40 feet (12m).
DIMMING:
We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.
WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE LOTUS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER – NO SERVICEABLE PARTS INSIDE.
Accessories
Accessories Sold Separately
Optional 120V – 347V Driver for LL2G-HO
0-10V Dimmable model # LLL-LD0612T
Low Voltage Extension Cables
6ft – model # EXC6 20ft – model # EXC20
Rough-In Plate
Model # RIP2
Trim Color Options
Available in White, Brushed Nickel and Black Trim
Downloads
Specification Sheets
Optional Driver for LL2G-HO : LLL-LD0612T
Extension cables : EXC-6 | EXC-20
Rough in plates : RIP2
Sell Sheets
PDF files
pdf LL2G-27K | pdf LL2G-30K | pdf LL2G-41K
pdf LL2G-27K-HO | pdf LL2G-30K-HO | pdf LL2G-35K-HO | pdf LL2G-40K-HO | pdf LL2G-50K-HO | pdf LL2G-3018K-HO
IES files
LL2G-27K | LL2G-30K | LL2G-41K
ies LL2G-27K-HO | ies LL2G-30K-HO | ies LL2G-35K-HO | ies LL2G-40K-HO | ies LL2G-50K-HO | ies LL2G-3018K-HO
Links to Energy Star
LL2G-27K | LL2G-30K | LL2G-41K
LL2G-27K-HO | LL2G-30K-HO | LL2G-35K-HO | LL2G-40K-HO | LL2G-50K-HO