6″ Sloped Round Regressed Gimbal

30° Sloped Trim for Wall Washing and Sloped Ceilings from 10° to 50°

MODEL: 15W: LRG6-6RSL | 18W: LRG6-HO-6RSL Category: Sloped Ceiling

Spec & Sell Sheets

Product Features

Models: 15W LRG6-6RSL, 18W LRG6-HO-6RSL
30° Sloped Trim for Wall Washing and Sloped Ceilings from 10° to 50°
Type IC Rated – Approved for Direct Contact with Insulation
Air-Tight, Wet Location, Insulated and Non Insulated Ceilings
2700K, 3000K, 3500K, 4000K, 5000K, Dim To Warm 3000K-2000K or 3000K-1800K, and 5CCT
Superb Light Quality with CRI 90+
Triac Dimmable with most CL dimmers 120V input
0-10V Dimmable Option 120V – 347V input
External Driver Inside Connection Box – No Junction Box Needed
Warranty: 10 Year on Residential, 5 Year on Commercial Installations
cULus Listed, Energy Star and T24 Certified (except Dim to Warm and 5CCT options)

Where to Buy

LRG6 360° View

Click & drag your cursor over the image to spin the image 360°.

Video Overview

Sloped Regressed Gimbals

Technical Specifications

CONSTRUCTION:
6″ Sloped Round Regressed Gimbal LED.
30° Sloped Trim for Wall Washing and Sloped Ceilings from 10° to 50°.
Class 2 Isolated external driver factory installed inside junction box. One driver for every fixture required.

MOUNTING:
Cut Hole In Ceiling And Snap Fixture In Opening With Attached Spring Clips.
Ceiling Clearance Required: 3 1/2″

Default Driver Triac Dimmable: 120V AC Input
Optional Driver 0-10V Dimmable: 120V-347V AC Input
Energy Used: Regular Version 15W or High Output Version 18W
Beam Angle: 38° Beam with 20° tilt and 360° rotation
Light colour options: Warm White 2700K, Soft White 3000K, Bright White 3500K, Neutral White 4100K, Daylight White 5000K, Dim to Warm 3000K to 2000K, 5CCT user selectable 2700K to 5000K
Light output 15W: Warm White 1100 lm, Soft White 1200 lm, Bright White 1250 lm, Neutral White 1300 lm, Daylight White 1400 lm, Dim to Warm 900 lm
Light output 18W: Warm White 1500 lm, Soft White 1550 lm, Bright White 1600 lm, Neutral White 1650 lm, Daylight White 1700 lm, Dim to Warm 1150 lm
CRI 90+
Ambient Operating Temperature: -40°F (-40°C) to +104°F (+40°C)
Compliance: cULus Listed, certified to CSA STD. C22.2 No. 250.0
Rated: Type IC (Direct Contact with Insulation), Energy Star (except Dim to Warm and 5CCT), Air-Tight

DIMENSIONS:

ID 6 1/4″; OD 7″; Thickness 4″
Cut out: 6 1/4″
Junction Box Dimensions (with driver inside): 3 3/4″ x 3 3/8″ x 1 1/2″
Junction Box Wire Capacity: Max 5 No 12 AWG or 8 No 14 AWG

Suitable for wet locations and soffit installations.

Installation

ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.

Gimbal LED Lights Installation:

CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove the knockout on the side plate. Install standard L16 cable connector. Insert line voltage feed into the cable connector and splice same colour wires using the included quick connectors. Close the cover. Connect the driver to the light fixture – the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand.

OPTIONS FOR LOCATING DRIVER:

Fixture comes connected to the driver by 15″ long low voltage cable with waterproof connector in the middle.
Depending on where you want the driver to be you have 2 options:

Locate next to the fixture.
Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 6 feet (1.8m) and 20 feet (6m). Cables are linkable.
Maximum run should not exceed 40 feet (12m).

DIMMING:

We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.

LIST OF COMPATIBLE DIMMERS

WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE LOTUS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER – NO SERVICEABLE PARTS INSIDE.